Wooden Side Panels

klerc · 2015-06-22T19:05:12.000Z

http://www.perfectcircuitaudio.com/ergonomic-end-panels-for-elektron-boxes.html

nedavine · 2015-06-24T03:22:42.000Z

I don’t like those screw in side panals as it amkes taking the boxes out for gigs annoying (also you can’T just take one of the machines and go play in the living room). I thought about building a simple version where the machines rest on a lip so you can just plonk the machine on it. Obviously this means the side panels need an adjoining piece of wood but hey.

Muddler · 2015-06-24T04:26:16.000Z

Yeah, I’m planning on using only 15 mm boards and a fairly less drastic angle. I also want to use the plastic cover.

Anyway, I have some good wood laying around and plenty of free time in early August so I’ll give it a try. If i don’t like, I won’t use them.

Least_Useless · 2015-06-24T07:17:24.000Z

""nedavine"":

I don’t like those screw in side panals as it amkes taking the boxes out for gigs annoying (also you can’T just take one of the machines and go play in the living room). I thought about building a simple version where the machines rest on a lip so you can just plonk the machine on it. Obviously this means the side panels need an adjoining piece of wood but hey.

brada_laptopstod_svart_0094156_PE231892_S4.JPG500×500 9.52 KB

I’m using this dirty cheap laptop stand from IKEA. Not a perfect fit but it does the job beautifully.

mokonline · 2015-06-24T16:39:01.000Z

wooden stand for elektron :
free engraving

www.zerack.com

Flat · 2015-07-16T19:16:41.000Z

I’ve reluctantly added vents to my panels. Personally I hate them, but to some they have to be there (I’ve been told they don’t).

Available if you want some

Elektron_Vent_QUAD.jpg1116×840 326 KB

TS_2501 · 2015-07-16T19:53:46.000Z

""andreamilana"":

SPIKE stands holding Elektron gear:

Spike_Cenk_Sayinli_Dataline.jpg720×400 118 KB

and the New KOSMO double stand:

4_KOSMO_by_cremacaffedesign_com.jpg720×400 141 KB

16_KOSMO_by_cremacaffedesign_com.jpg720×400 133 KB

Keep on Playing!

KeepOnPlaying_Cremacaffedesign_com.jpg720×400 92.7 KB

cremacaffedesign.com

don’t mean to start a war but 60€ for some thin slices of wood is ridiculous. looks neat though. and the wooden side panels are ugly as sin. but meh… i might not be your target audience.
if you just want your gear to stand up right, have a look at the my cheap ikea hack: 11€ Elektron Stand IKEA Hack - Album on Imgur

chrome-metronome · 2015-09-08T18:07:14.000Z

""TS_2501"":

if you just want your gear to stand up right, have a look at the my cheap ikea hack: 11€ Elektron Stand IKEA Hack - Album on Imgur

Badass. Looks like a great option!

""Flat"":

I’ve reluctantly added vents to my panels. Personally I hate them, but to some they have to be there (I’ve been told they don’t).

Available if you want some

Elektron_Vent_QUAD.jpg1116×840 326 KB

These are the tidiest looking ones out there imo. How much and where?

Flat · 2015-09-08T18:47:05.000Z

[quote=““chrome-metronome””]

TS_2501:

if you just want your gear to stand up right, have a look at the my cheap ikea hack: 11€ Elektron Stand IKEA Hack - Album on Imgur

Badass. Looks like a great option!

""Flat"":

I’ve reluctantly added vents to my panels. Personally I hate them, but to some they have to be there (I’ve been told they don’t).

Available if you want some

Elektron_Vent_QUAD.jpg1116×840 326 KB

These are the tidiest looking ones out there imo. How much and where?[/quote]
here:
http://www.ebay.co.uk/itm/151806342430?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649

chrome-metronome · 2015-09-08T22:27:37.000Z

wicked. my RYTM may have to be swapped back in Stockholm, but I have it bookmarked!

They come with a gap for ventilation too, correct?

jbhelp · 2015-09-09T14:36:56.000Z

Here is my small laser cut diy project.

sketch.jpg972×612 52.2 KB

real.jpg2048×1536 404 KB

BoBSwanS · 2015-09-10T10:20:13.000Z

Little tip for those with wooden cheeks and a wooden desk.
Buy some industrial grade sticky velcro to stop them sliding around all over the place

A small strip on the bottom of the cheeks and then a small strip on the desk and it will be solid as a rock and easily removed from the desk

jbhelp · 2015-09-10T12:02:55.000Z

I used this one:

3M_SJ5312_1.jpg800×535 31.4 KB

this is fantastic! no slipping at all and you can buy it pretty almost everywhere.
like here
http://store.moltenvoltage.com/Rubber_Feet_4_Self_Adhesive_3M_0_14_thick_x_0_p/hard_009.htm

chrome-metronome · 2015-09-10T21:34:57.000Z

""jbhelp"":

real.jpg2048×1536 404 KB

sick! do you plan on making them available to others ?

psynthetic · 2015-09-11T06:37:56.000Z

""jbhelp"":

I used this one:

3M_SJ5312_1.jpg800×535 31.4 KB

this is fantastic! no slipping at all and you can buy it pretty almost everywhere.
like here
http://store.moltenvoltage.com/Rubber_Feet_4_Self_Adhesive_3M_0_14_thick_x_0_p/hard_009.htm

Thanks for the link

jbhelp · 2015-09-11T07:41:42.000Z

""chrome-metronome"":

[quote=“jbhelp”]
real.jpg2048×1536 404 KB

sick! do you plan on making them available to others ?:D[/quote]
maybe, I am planning to add a finger-screw option for removing the side panels easily to put elektron devices in bags for gigs, also there will be different colors available. but this is all in future

guga · 2016-01-01T21:26:44.000Z

…spent few hours to hand-cut some plexiglass and make a couple of side-panels for my AR and MM

guga · 2016-02-23T00:09:59.000Z

…made a better version

rvrs.jpg384×582 79 KB

this panels are made out of MDF, they’ve been laser cut so they can also be engraved with logos and whatnot (this will add to the final price). the design needs to be refined a bit and then they will be ready to join the list of all the others already available

i should be able to have a couple of choices for the material and different colors as well. more info to come. in the meantime, if anyone is interested, please do get in touch.

Ozone · 2016-02-23T00:32:43.000Z

""guga"":

…made a better version

ngl.jpg640×384 81 KB

this panels are made out of MDF, they’ve been laser cut so they can also be engraved with logos and whatnot (this will add to the final price). the design needs to be refined a bit and then they will be ready to join the list of all the others already available

i should be able to have a couple of choices for the material and different colors as well. more info to come. in the meantime, if anyone is interested, please do get in touch.

Nice one Guga! Looks great. Noticed reversible vent holes on the rytm side but not on the mm side though? How many mm’s are you allowing for the screws into the MM?

Also been thinking about frames lately, with the lack of new EIT1’s available, & wanting something that folded. Just posted this one in another thread yesterday and thought it might warrant a re-share here.

2000×1500 336 KB

2000×1500 251 KB

jbhelp · 2016-03-30T07:03:31.000Z

PL-2 compatible 2-tier Elektron Stand which I made for a couple of my customers: