Who's using an A4 cv to Modular?

avantronica · 2016-10-10T14:54:47.307Z

Callofthevoid:

If I use the CV track + the FX track will that give me 2 x ‘pitch+gate’? Leaving me still the 4 internal A4 synth tracks to use ‘normally’?

Yep That’s the normal approach

Lukree · 2016-10-10T15:51:46.748Z

Callofthevoid:

What’s the deal with midi>cv conversion boxes? Maybe I’ll look at that route and then be able to use 3 OT midi tracks to send 3 separate pitch sequences to the Dom1 Oscs? Don’t know if possible/feasible/costly… Need to do me some reading…

I’m using this Vermona midi module with a DAW and eurorack, one plus side with that is that you can configure it to use chords. Perhaps it’s not so convenient with Octatrack and Dom1 is mono, but it would be interesting to test. Shame that A4 cannot send midi out from sequencers…

https://www.modulargrid.net/e/vermona-qmi2-quad-midi-interface

insect · 2017-01-09T15:01:16.253Z

nice tread! my modular gas has already started with the dark energy and some modules ^^

I find A4 very good to sequence one modular voice (e.g. using the A4 arp ) and sending out clocked lfo modulated envelops for vca and / or filter.

yesterday I wantet to use another sequencer for the dark energy 2. I remembered that my xoxbox has also cv/gate outs (and Octave One praised their Xoxbox a lot for cv/gate seq) … so I hocked up the xoxbox cving the Dark Energy 2. Xoxbox getting Midisync from the A4 and A4 is send cv/env out to braids and filter.

But Dark Energy was slightly late in timing! I set the TDLY in braids to about 4ms to be on time.

What could be the problem? Midi Timing issues with the A4? Midi Timing issues with the Xoxbox? The snowy cold weather in Germany?

Btw … what vca do you use? Has anyone the MI Veils?

sinsyn · 2017-01-27T09:36:38.203Z

All sequenceing and clocking from A4 all modular sounds

analept · 2017-01-27T11:51:21.507Z

nice !!! really great sounds !

sinsyn · 2017-06-04T12:53:17.335Z

Thank you.

sezare56 · 2017-11-16T01:23:01.394Z

Does anybody tried the inexpensive XOX Heart ?

http://www.openmusiclabs.com/projects/x0x-heart/index.html

phil71 · 2018-01-20T19:38:01.190Z

A4 CV to a pair of semi-modular synths

A4 CV sequencing both the MS-20M and the Microbrute at the same time.

3 oscillators into the MS-20 filters, the LPF being modulated by the A4 envelope (fast modulation) and LFO (slow & random modulation). The FM and sync have been engaged in the MS-20M.

Finally, the sound from these 3 osc, after going through the MS-20 filters, go directly into the A4 Ext input in order to take advantage of a great amount of <3 Chorus, Delay & Reverb <3

20180119_175833 (2).jpg4032×2268 1.74 MB

I especially appreciate the junction sockets on the MS-20M. It functions like a CV cable splitter (you can see one unused at the bottom edge).

Here are the CV parameters of my system:

cv.jpg741×701 152 KB

My first track from this setup:

ericg · 2018-01-21T22:41:22.469Z

Im in this boat now at the min. Was working fine the other day except tonight the A4 only sends out notes to the Temps Utile when the arp is on or I play the A4 key board. Won’t play from trig notes. Anyone experienced this?tks

ericg · 2018-01-21T22:54:22.576Z

ok noticed that I need to have Note length on the note page down to minimum unless Im using the arp.

KaOsphere · 2018-01-21T22:55:45.944Z

Got something similar the other day, solved it by tweaking the voltage output/clock div on the A4.

ericg · 2018-01-21T23:02:35.720Z

Ok thanks will keep that in mind. Was getting worried when it just stopped sending out notes or gates.

Dapifer · 2018-01-22T14:39:41.291Z

So you can send lfo via CV from the A4?

slicetwo · 2018-01-22T14:41:36.098Z

Yes.

Dapifer · 2018-01-22T15:06:20.453Z

Ah so you can attenuate the signal within the A4? I have some pedals that will only accept 5v so would be good to be able to attenuate it without having to buy extra cables.

avantronica · 2018-01-22T15:13:20.624Z

You don’t attenuate - you just define upper and lower voltage limits - this voltage high e.g. becomes the peak of an env or lfo

The Max is +10V , min -10V and it can be set in mV (10mV steps)

phil71 · 2018-01-22T23:01:45.575Z

Yes, you can.
In my table (a few posts above), the CV C is connected to the cutoff frequency of the low-pass filter of the MS-20. You just have to set the destination of one of the two LFOs from the A4 to the value of CV C

AGP1 · 2018-01-23T00:04:32.109Z

i have just the rings and clouds powered by my A4 right now. LFOs from CV b/c/d doing … stuff to both modules and CV A doing pitch on the rings (doesnt need a gate control here)

I’ve been looking at expanding into some other modules but not quite sure where to go with them. 4ms spectral resonator looks pretty special…

Dapifer · 2018-01-23T09:29:47.536Z

Thanks. So would I be right in saying I can use 4 tracks using the A4 voices, 1 track sending CV gate and pitch, and then utilise the FX track as CV for modulation?

avantronica · 2018-01-23T09:32:07.512Z

Not really - you can use the FX track for sequencing - so only pitch gate as modulation sources

You can use the CV track for sequencing and simultaneously for separate control of envelopes/lfos/clock/etc - the Value Lin(ear) Mode used to generate general modulation CV signals is only on the CV track as a destination