Who's using a Qunexus and how?

Lymtronics · 2015-03-05T18:47:03.000Z

I use the Qunexus with a Kenton USB midi host. The retailer warned me that I would need the KMI midi expander to get the results I was after, but it is not the case. I thought I’d put that out there since the Kenton is more versatile and can be used with gear such as the OP-1 to control or be controlled by other gear.

rempdx · 2015-04-03T06:33:17.000Z

Hey guys,

I just got a QuNexus to control my A4.
I tried to edit some presets with the editor but I am still not getting some interesting results.

Looking for some presets/tips/ideas. Basically need more expressivity when I am playing the A4 live (pressure, velocity etc…).

Thanks!

rempdx · 2015-04-05T20:22:19.000Z

Also having some issues when controlling the A4 from the Quenexus (monophonic setting).

When I am playing a track from the Quenexus (for example a lead), the new note cuts off as the previous note is released. Note sure if this is a velocity issue or a Quenexus bug. Playing the same patch from the A4 keyboard works fine. Thoughts?

jim5 · 2015-04-15T12:49:39.000Z

""rempdx"":

Also having some issues when controlling the A4 from the Quenexus (monophonic setting).

When I am playing a track from the Quenexus (for example a lead), the new note cuts off as the previous note is released. Note sure if this is a velocity issue or a Quenexus bug. Playing the same patch from the A4 keyboard works fine. Thoughts?

Screen_Shot_2015_04_05_at_1_24_01_PM.png585×413 66.6 KB

Turn the velocity off from Quenexus and see what happens. You can do it without the computer by holding down the preset button for few seconds then turning on/off various features.

rempdx · 2015-04-23T17:44:35.000Z

Thank you I actually ended up selling the A4+QueNexus combo to replace it with the AK.

Jaspmf · 2015-08-11T00:32:05.000Z

""subq"":

I have one with the midi extender. It is actually my main external keyboard. However, I’m going from OT midi in, then midi out from there to everything else, including my A4. That allows me to sequence everything with it.

How did you get it to work in this setup?
I have OT, A4, Rytm and just got Qunexus.
Before the Nexus I just had the gear setup OT MIDI OUT>Rytm IN, Rytm THRU > A4 IN.

If I go Qunexus directly into the A4 it works perfectly. (OT + rytm aren’t hooked up)

If I have it go to OT IN with my normal chain (OT MIDI OUT>Rytm IN, Rytm THRU > A4 IN) it doesn’t do anything.

Tried going OT OUT > Rytm IN, Rytm THRU > MidiXpander IN, MidiXpander OUT > A4
That kills the MIDI on the A4 (no clock from OT etc) But the Qunexus controls it fine in this setup.

Any advice?

PeterHanes · 2015-08-11T18:23:36.000Z

""Jaspmf"":

[quote=“subq”]I have one with the midi extender. It is actually my main external keyboard. However, I’m going from OT midi in, then midi out from there to everything else, including my A4. That allows me to sequence everything with it.

How did you get it to work in this setup?
I have OT, A4, Rytm and just got Qunexus.
Before the Nexus I just had the gear setup OT MIDI OUT>Rytm IN, Rytm THRU > A4 IN.

If I go Qunexus directly into the A4 it works perfectly. (OT + rytm aren’t hooked up)

If I have it go to OT IN with my normal chain (OT MIDI OUT>Rytm IN, Rytm THRU > A4 IN) it doesn’t do anything.

Tried going OT OUT > Rytm IN, Rytm THRU > MidiXpander IN, MidiXpander OUT > A4
That kills the MIDI on the A4 (no clock from OT etc) But the Qunexus controls it fine in this setup.

Any advice?[/quote]

I don’t have a QuNexus but (with the KMI MIDI Expander) it should work just like any MIDI keyboard. That means that you will need to ensure that the MIDI channels are set up appropriately on each Elektron instrument.

Connect the MIDI Out of the MIDI Expander to the MIDI In of the OT. Set the MIDI channel for the MIDI Expander to be the same as that of the Auto channel of the OT. Then, when the OT is in MIDI sequencer mode, it will pass on what you play through its MIDI Out port to the connected instruments.

You will need to set the MIDI channels of the OT’s MIDI sequencer tracks to match the channel numbers you have set for the tracks on the AR and AF that you want to play using the QuNexus. You will probably need to deactivate MIDI receipt for some of the tracks on the AR and AF in order to prevent conflicts.

Madchiller · 2015-08-11T18:42:06.000Z

I am using the qunexus with midi expander.

Octatrack out to midi expander. Cv out of qunexus to modular. Works pretty well for one track. I get one gate and 3cv this way. Plocked cv control! Wicked!

I did however try the expert sleeper fh1 with this combo and it works great! Adding 8 channels of gate/cv to the setup… Really sick!

subq · 2015-09-04T19:16:20.000Z

""Jaspmf"":

[quote=“subq”]I have one with the midi extender. It is actually my main external keyboard. However, I’m going from OT midi in, then midi out from there to everything else, including my A4. That allows me to sequence everything with it.

How did you get it to work in this setup?
I have OT, A4, Rytm and just got Qunexus.
Before the Nexus I just had the gear setup OT MIDI OUT>Rytm IN, Rytm THRU > A4 IN.

If I go Qunexus directly into the A4 it works perfectly. (OT + rytm aren’t hooked up)

If I have it go to OT IN with my normal chain (OT MIDI OUT>Rytm IN, Rytm THRU > A4 IN) it doesn’t do anything.

Tried going OT OUT > Rytm IN, Rytm THRU > MidiXpander IN, MidiXpander OUT > A4
That kills the MIDI on the A4 (no clock from OT etc) But the Qunexus controls it fine in this setup.

Any advice?[/quote]
I missed the notification on this…sorry for the late reply, did you get it working? Basically, it should just be about auto-channel config and whatnot…I can hit everything in the system from kb and it goes into the OT…I’ve run MIDI straight to A4 and Rytm and everything else and also run MIDI to A4 and then thru to Rytm for example no problems…I even interface into modular and use kb on that too (not using the CV outs on kb)

Terrific_Broth · 2015-10-30T13:50:16.000Z

Hi all

Wanted to check with users on a couple of things before I go ahead on this And possibly midi expander too:

Does it have a separate psu allowing me to use it without a computer or is it all USB powered?
I have an Iconnect midi2+. Would this work like the expander, power the unit and hook up to my DIN hardware?

thanks for your help

nfim · 2015-10-30T17:27:53.000Z

[quote=““Terrific Broth””]
Hi all

Wanted to check with users on a couple of things before I go ahead on this And possibly midi expander too:

Does it have a separate psu allowing me to use it without a computer or is it all USB powered?
I have an Iconnect midi2+. Would this work like the expander, power the unit and hook up to my DIN hardware?

thanks for your help
[/quote]

It can be bus powered if you’re using a computer but to use without a computer you need the midi expander, which requires a psu.
I think only the iconnect 4 has usb host capabilities.

Terrific_Broth · 2015-10-30T17:42:37.000Z

Thanks Anfim

sleepytm · 2017-01-05T09:36:52.808Z

ok, so i’ve tried to get into using qunexus with a4 once again, with pressure and tilt functions mapped to modulation wheel or breath controller or aftertouch settings… and it’s pretty tricky to play, cause if you map filter resonance to pressure, for example, it’s always somewhere in the middle, not from zero value. so as you playing, you don’t get the same results, as with a4 keyboard…
i mean, guys, how do you use it? or do you use pressure and tilt stuff at all?

also i turned pitch bend stuff off, cause it gets so difficult to play in key.

sezare56 · 2017-01-05T09:38:50.894Z

Try A4 Perf settings on filters if you can.

sleepytm · 2017-01-05T09:42:02.672Z

yeah, it’s just i’m thinking that it’s so much better to get arturia keystep, for complimenting a4

sezare56 · 2017-01-05T09:57:11.731Z

I’m happy with my Korg Tk49. Good sync arp, good pads, standalone, very customizable. No after touch.

wovertices · 2017-10-19T14:41:51.080Z

Sounds great…tell me more about setting the QN up with the AF? Please be specific…much appreciated…John

izzymonkey · 2017-10-21T15:01:03.207Z

I’ll try—I have an Analog Keys now since selling the A4 some time ago. The Keys has the level of expression I wanted out of the A4 + QN pairing; it’s keybed with aftertouch plus mod/breath/pitch joystick works really well.

When I did run the A4 + QN, the MIDI Expander simply connected to the A4 via MIDI DIN, as you’d expect. I didn’t have to do anything with the QN itself in terms of setup. Overall, when I first got the QuNexus I did mess around with some of its settings using the app on my Mac. Primarily the touch sensitivity settings—the default curve was not giving me a pleasing range of input. It felt too quick to ramp between my typical playing pressure and WHOA FULL Values. I tweaked the curve to suit my playing style, which made it much easier to get more nuanced expression from the A4, e.g. Modulation from 0 - 64 on any given patch.

Ultimately, the Keys was just more immediate, more aligned to actual performance needs. I haven’t used the QN for anything since, expect perhaps for some rare, just-for-fun noodling on an iPad synth app.

wovertices · 2017-10-21T23:13:02.087Z

Thanks so much; I appreciate you getting back to me…I will tweak the QN settings as you suggest!
Best,
John
www.johnjpotter.com

Chinchilla · 2020-07-05T17:24:08.142Z

Possibly a really stupid question, but I’ve just found a KMI Qunexus in a cupboard!
As it’s supposedly Class Compliant, would I be a be able to use a micro USB to female USB joined with a standard micro USB cable and use it to control the M:C for example, or any synth with midi over USB?