[ Sound Pack + eLearning ] Lowend101 eBook Delivered in 3 parts (Thanks to v00d00ppl)

When the sounds need more bite…
Drum Layering and Compression (Transient method) does not really make sense if the job is at the Layering step is well achieve … A glue compression bus is much smarter then :slight_smile:

Excellent stuff! Will need to check this out tomorrow. Looking forward to learning. Thank you!

1 Like

Thanks @Studio_Cee

1 Like

LOWEND Article 05 : SubDamaged Patch

( Movement, Wobblish Sub BASS Sound-Design exercise )

Normally you should have your Unison activated in Poly Config and Voice 1 and 2 checked ! if not please go back to Article 3 to see how Poly Config is Set.


Let’s dive right in here :brown_heart:

2 Likes

LOWEND Article 06 : 808Sub Patch

( Punch, LowEnd Sub BASS Sound-Design exercise )

Normally you should have your Unison activated in Poly Config and Voice 1 and 2 checked ! if not please go back to Article 3 to see how Poly Config is Set.


Let’s dive right in here :boom:

2 Likes

Side Note :

In the END of the Article 06 on 808 Sub Bass, i encouraged you to experiment in the What’s Next section. Coming back to that to speak about a fundamental notion in Sound Synthesis :

Saving Iterations
I can only insist on this point, it is essential really! Because you probably heard about the “Sweet Spot” notion…i don’t really like this designation anyway, there’s “Sweet Spots” and trust me there’s a LOT… You experiment and you will find some pleasant things to happen…

Quite honestly every time you make a baby smile at birth, you’re stuck on a melody with the current setup … it’s very likely that it’s an iteration to back up ! So please when it’s happen think to me and say oh william told me about that moment… i will copy the sound TRK1 Copy and i will paste it on TRK2 before i screw it… or Sound Manager > Store TRK sound… And call it : whateverthenameyourwant-01

And as long as you have not re-initialized your TRK to start on a brand new sound-design. Each time you see this baby smile or you find a tasty melody with a different sound from the whateverthenameyourwant-01 AGAIN SAVE IT to whateverthenameyourwant-0203, 04, 05, 06, 07, 08 You don’t care you 14 bank…

You will previewing later all iterations and keep only the ones you really like… maybe the next day ! it’s a good practice to let your ears calm down and coming back on your sounds with clean ears… There’s things you gonna dislike and things you like even more… maybe you will tweak it again and save a much better version of it.

DONT LOST SOME SOUND DESIGN or SWEET SPOT because at some point you will be tired and you will switch OFF you machine ! and if you haven’t saved your iterations … you may have lost one afternoon plain and simple and it’s not good !

3 Likes

Of course it’s the beginning so it’s start from the basics, it’s easy for now… BUT

I’m curious to have feedbacks from you…

Or any thoughts you can come with don’t hesitate to reach me, PM if you prefer, publicly as well :wink:

@William_WiLD it’s taken me a while to get around to auditioning the new pack, after downloading minutes after initial release! However very impressive work mate.

You should feel proud of yourself.

1 Like

William_WiLD you are too good to us. :rocket:
I’m busy too much for a proper studying, but looking forward to printing as you say and having it with a coffee by my A4. You bet!
Thank you :sailboat:

2 Likes

Yes i imagine there’s people would like to experiment/study like i do with a full document printed on table.

Thanks for those feedback !

Don’t stop i can eventually refine few things if necessary and please note that those sounds covered in Article are NEW and not inside the Sound Bank…

3 Likes

LOWEND Article 09 : TKN_BASS 01

( Punch, BASS Crafted with TP-808BASS Starter Template file )

Normally you should have your Unison activated in Poly Config and Voice 1 and 2 checked ! if not please go back to Article 3 to see how Poly Config is Set.



How to use this Patch ?

The TKN_BASS 01 is in two parts layering… so you can use it as a Tom/Chord Percussive BASS for few notes as well as a LOWEND rollin with the parameter Slide… And removing with P-Locks the Tom/Chord Percussive Part every where you don’t want it as i done here… You can tweak it also to your own taste :slight_smile:

2 Likes

These are awesome tutorials William. Thank you.

1 Like

I’ve been away for a few days so I’m slow to respond. Excellent work William. This is a phenomenal amount of your time that you are sharing with us and I totally appreciate what you are doing. I love the presentation. It is clear and easy to follow but offers the challenge and inspiration to get hands dirty and experiment. Very cool!

2 Likes

Thanks @djx it appears that most people wait to print the booklet to get started on the desk which i can perfectly understand that’s the way i prefer too :wink:

i make my best to finish around January/February :slight_smile:

(Edited because I don’t think the booklet will be ready in 2 days.)

Yes thats me…I’ll get the whole book then sit down on couch feet up and start learning with A4 in headphones.

1 Like

I have two hard drives that have the same names Samsung D3 and T3, I launched a formatting procedure on the bad one !

I tried to unplug the drive to simulate a power failure that happens at the right time. But that did not work.

On this 6To disk there is a lot of things (included LOWEND) that I try to recover with Data Rescue. (Stellar Phoenix did not give anything) That’s what I’m in at the moment and why you people do not see / hear me too much right now …

Shit.
That’s really hard, friend !

1 Like

Ahh man…thats no good…feel for you.

1 Like

:scream:

1 Like

Think I’m done with all this crazy TO Hard-Drive… next time I will buy 3 x 2 To instead one 6 To
:frowning: