MNM freeze

bluewolfse7en · 2015-02-10T23:04:52.000Z

It won’t be the battery on a machine that age, not unless it’s faulty anyway.
I sent my MD back a few years ago & it cost me €175 inc vat & shipping.
It’ll all depend on components I guess. Labour is charged by the 1/2 hour I believe but they seem to get an awful lot done in that time.

Best of luck

Matthewsavant · 2015-02-28T07:50:16.000Z

""lohacker"":

thanks bluewolfse7en for the interest and advices,

Never moved it from my desk in more than a year, i bought i second hand in late 2012 but it’s a 2010 unit with + drive.
I’ve already contacted elektron support, probably I have to send in it for repair. Do you know how can expensive the repair could be in best/worst case scenario?

lohacker,
Any status update?
I am experiencing the same exact issue with my MNM it just started tonight and I’ve tried all the same things you have and have had no luck. I was about to make a post for my issue but it seems like what people have suggested are the only options.
I contacted Elektron a few hours ago and I’m hoping it’s something that can be fixed without sending it away or paying a lot for repairs. I can’t afford to put any money into it right now never mind a replacement
I’m freaking out about it because I’m in the middle of a job and was using the MD and MNM heavily!
And on top of that I love the Elektron boxes and own all of them except the OT (Which is on its way) but these things are indispensable and I planned on owning and enjoying them for the rest of my life, So this really fucking sucks!

guga · 2015-02-28T18:50:34.000Z

i would have a look inside; could be a loose cable or it could be that the MM you bought was already old enough an you’ll need to replace the battery.
either way, i would give it a go before sending it back to the HQ

zfigz · 2015-02-28T20:08:23.000Z

""guga"":

…it could be that the MM you bought was already old enough an you’ll need to replace the battery.

is battery installation fairly straight forward and easy to do?
i’m asking in case i ever need to do it

lohacker · 2015-03-03T00:02:28.000Z

Hi guys,
sorry for late reply, I was a bit busy these days, anyway I decided to sent my MNM back at HQ for repair, it needed a CPU board replacement and now it’s on its way back home

biologik · 2015-03-30T13:11:26.000Z

I just wanted to give a little update to this.
I’ve been enjoying my RYTM and A4 so much I haven’t turned on my MnM in a while. Last night I wanted to have a go. I turned it on as normal, and then it froze after about 40 secs.
Turned it on again and it froze at the loading page. Turned if on again and it froze at a different point in the loading page. I did this a bunch of times in maybe one in 10 times it made it to the regular play screen but then froze shortly after

Today I opened up my MnM to see if there were any loose cables or something simple like that. Nope.

Put it all back together and now it loads OK (every time), but feezes after about 40 secs.

EDIT: I just got a “battery low” notice. I’ll change that battery (it’s a simple slip-out battery) and report back! I don’t feel like opening it up again today, but will soon.

biologik · 2015-03-30T22:11:58.000Z

Well, I ended up changing the battery today.

After doing that, I gave it a reboot and it loaded fine. It played for a few mins (maybe 5?) and then it froze.

Then, I gave it a reboot and hit play. It played for an hr and never locked up.

Rebooted again. Loaded fine. Hit play. Played for 2 hrs. No lock ups.

Maybe it was a battery issue? I’ll report back if it starts to freeze again.

biologik · 2015-03-31T14:52:43.000Z

I have a MK II UW+
It was held by a tab, not soldered.

No freezing issues anymore… not sure if related, but all is well now.

biologik · 2015-03-31T15:01:51.000Z

HQ said that this can be caused by some oxidation on the cabling and that you can use oil-free dry cleaning spray to remove this from the cable connectors and sockets.

I must have inadvertently done this when moving and putting the sockets on/off and basting unit with air.

HQ: “If you are comfortable with disassembling the unit, like you must have done to change the battery, we recommend that you use a dry oil-free cleaning spray to remove oxide from the two connectors and sockets of the internal cabling.”

AdamJay · 2015-09-24T00:45:26.000Z

""biologik"":

HQ said that this can be caused by some oxidation on the cabling and that you can use oil-free dry cleaning spray to remove this from the cable connectors and sockets.

I must have inadvertently done this when moving and putting the sockets on/off and basting unit with air.

HQ: “If you are comfortable with disassembling the unit, like you must have done to change the battery, we recommend that you use a dry oil-free cleaning spray to remove oxide from the two connectors and sockets of the internal cabling.”

So, this has been happening to my SFX-60+Mk2 again.
I opened it up to use the cleaning spray again, and now it won’t boot.
Opened a ticket. Pretty bummed

no_barcode · 2015-09-24T00:50:45.000Z

""AdamJay"":

[quote=“biologik”]HQ said that this can be caused by some oxidation on the cabling and that you can use oil-free dry cleaning spray to remove this from the cable connectors and sockets.

I must have inadvertently done this when moving and putting the sockets on/off and basting unit with air.

HQ: “If you are comfortable with disassembling the unit, like you must have done to change the battery, we recommend that you use a dry oil-free cleaning spray to remove oxide from the two connectors and sockets of the internal cabling.”

So, this has been happening to my SFX-60+Mk2 again.
I opened it up to use the cleaning spray again, and now it won’t boot.
Opened a ticket. Pretty bummed :([/quote]
That really sucks. Do you think the spray caused additional issues?

AdamJay · 2015-09-24T00:57:12.000Z

""no_barcode"":

[quote=“AdamJay”][quote=“biologik”]HQ said that this can be caused by some oxidation on the cabling and that you can use oil-free dry cleaning spray to remove this from the cable connectors and sockets.

I must have inadvertently done this when moving and putting the sockets on/off and basting unit with air.

HQ: “If you are comfortable with disassembling the unit, like you must have done to change the battery, we recommend that you use a dry oil-free cleaning spray to remove oxide from the two connectors and sockets of the internal cabling.”

So, this has been happening to my SFX-60+Mk2 again.
I opened it up to use the cleaning spray again, and now it won’t boot.
Opened a ticket. Pretty bummed :([/quote]
That really sucks. Do you think the spray caused additional issues?[/quote]
Hard to say. It remedied the issue and without any symptoms for months following. Now the suggested remedy just isn’t working.

dekalboy · 2015-09-27T10:39:40.000Z

I have no freezing problem of these type.
but today , my monomachine also freeze when I was keeping switching between SONG and PATTERN mode to make movement in my music,

( because I recently realize that the monomachien keeps the song setting ( with offset setting, mutes etc … ) when you switch back into pattern mode , that’s awesome. )

But it freeze only one time , I don’t know why ; I have repeat the same and nothing happen.
really stange.

faxekondi · 2015-10-18T20:15:49.000Z

""AdamJay"":

So, this has been happening to my SFX-60+Mk2 again.
I opened it up to use the cleaning spray again, and now it won’t boot.
Opened a ticket. Pretty bummed

Any update on your situation? I am experiencing the same problem with a freezing Monomachine. I also notice the machine is nearly always instant to freeze when I insert/remove cords from the headphone and output jacks. It seems like I could be experiencing this oxidation issue you mentioned, but I’m worried about bricking the synth if I do a DIY spray job.

natrixgli · 2015-10-19T04:43:35.000Z

Recently had a problem with my MNM freezing, ultimately turned out to be a bad power supply.

AdamJay · 2015-10-20T15:46:04.000Z

""faxekondi"":

[quote=“AdamJay”]So, this has been happening to my SFX-60+Mk2 again.
I opened it up to use the cleaning spray again, and now it won’t boot.
Opened a ticket. Pretty bummed

Any update on your situation? I am experiencing the same problem with a freezing Monomachine. I also notice the machine is nearly always instant to freeze when I insert/remove cords from the headphone and output jacks. It seems like I could be experiencing this oxidation issue you mentioned, but I’m worried about bricking the synth if I do a DIY spray job.[/quote]
Sent it into Elektron some weeks ago. They said they are replacing the internal power supply.
I’ll update when I receive it back.

faxekondi · 2015-10-23T00:08:18.000Z

I decided to open up my Monomachine since it’s out of warranty to see if it was a ribbon issue. After readjusting them, my unit has stopped freezing. I’ve let it play for the past few hours and all seems to be good. Hopefully this remedied the problem however only time will tell.

I hope your machine is as good as new after professional service, AdamJay. It would be great if you could still provide an update, especially regarding costs, if out of warranty.

Saldiamond · 2016-10-22T04:41:24.846Z

Had the same problem as OP.
As per support suggestion, I disassembled the unit and reseated the connectors and so far (1 hour of use) it appears to have resolved the issue.

P.S. I am terrible at Electrical/mechanical stuff but it was not that difficult.

Thanks

LFOKringlan · 2017-02-28T10:55:30.405Z

Omg I got the same issue now! Exactly the same! What do I do??

image.jpeg2592×1936 1.24 MB

PeterHanes · 2017-02-28T13:05:01.072Z

Open a support ticket with Elektron via their website and they will guide you through the process.