How to change patterns via midi?

Smokey · 2016-09-13T21:21:08.870Z

Thank you so much for the breakdown Peter.

So, if I decided to stay within banks A-D, I could have 64 patterns mapped and ready for use with a 64 pad controller?

PeterHanes · 2016-09-13T21:58:25.753Z

Smokey:

So, if I decided to stay within banks A-D, I could have 64 patterns mapped and ready for use with a 64 pad controller?

Yes, assuming that your controller can send a Program Change message from each pad.

Smokey · 2016-09-13T22:15:56.186Z

I believe the LaunchPad and Launch Control XL both MIDI and CC messages, so I should be good!

I have yet to purchase them so if someone sees and issue with those controllers and my intention for them (see a few posts up) please let me know.

robotron · 2019-06-23T21:55:47.387Z

Would I be able to change to patterns 1-16 within whatever bank I was in? So use up to 16 pads/pedals and just change the bank manually on the device itself? I’m guessing midi program change messages might not work that way, but I use each bank for a different song so it’s way more practical to just be able to switch within any active bank using the same 16 controller messages (rather than needing to program 64 or 128 individually)…

PeterHanes · 2019-06-23T22:13:57.023Z

robotron:

Would I be able to change to patterns 1-16 within whatever bank I was in? So use up to 16 pads/pedals and just change the bank manually on the device itself? I’m guessing midi program change messages might not work that way

Indeed, MIDI Program Change messages do not work that way.

If your controller device/software is programmable, it might be able to remember which pattern is active and to figure out the MIDI PC number that you need for your next pattern.

robotron · 2019-06-26T17:45:30.565Z

Thanks. I feared as much and the workarounds might be a bit too fiddly for me. I’ve never had much use for PC messages, seems like they were designed to call up a specific/predefined preset in a live set when I usually want to use them to browse patches/jam along with patterns. Ah well, can’t have everything!

Tokin_Tone · 2019-07-17T11:32:39.460Z

Hi. Thanks for this useful info. I am setting up a footpedal (Behringer FCB1010) to send PC messages to change patterns on my OT, but although I had it working originally, it now seems to select Patters I01 onwards, even though I’m sending PC0 etc, and I have bank 1 selected on the OT (I can’t seem to send bank change messages from the FCB)
Any ideas ?
Thanks

PeterHanes · 2019-07-17T12:01:01.697Z

Tokin_Tone:

I am setting up a footpedal (Behringer FCB1010) to send PC messages to change patterns on my OT, but although I had it working originally, it now seems to select Patters I01 onwards, even though I’m sending PC0 etc, and I have bank 1 selected on the OT (I can’t seem to send bank change messages from the FCB)
Any ideas ?

On OT, if you are not already in the half of the pattern banks (A-H or I-P) that you want, you need to send a MIDI CC 0 message:

with a value of 0 to access pattern banks A-H or
with a value of 1 to access pattern banks I-P.

That CC message then needs to be immediately followed by the Program Change message.

Tokin_Tone · 2019-07-18T07:22:24.921Z

Great, thanks

TapeTwelve · 2019-07-30T23:27:42.348Z

This has all been very helpful as ive just found the need for it.

Anyone know if you can use a foot switch to increment patterns?

All of the above seems to relate to selecting specific patterns (correct me if I’m wrong), which is great, but would be really handy to have one foot switch that triggers the next pattern, then the next bank after pattern 16 in each bank.

Am i asking for too much?

PeterHanes · 2019-07-30T23:46:19.606Z

TapeTwelve:

Anyone know if you can use a foot switch to increment patterns?

Here is an example:

Incrementing/decrementing pattern number using sysex Elektron Gear

OK,now I understand a little more what you want to do. As far as I can see, you don’t need MIDI SysEx messages at all. All the Elektron instruments allow you to select the next pattern by sending a MIDI Program Change message with a value that matches the pattern that you want to switch to (value 0 = pattern A01, value 1 = pattern A02 etc). I looked at the User’s Guide for the Soleman and saw that its Scene Mode steps through its own programs in sequential order and that you can use the Solema…

roadmoviemusic · 2019-07-31T10:53:02.176Z

TapeTwelve:

but would be really handy to have one foot switch that triggers the next pattern, then the next bank after pattern 16 in each bank.

It’s possible to write a Arduino sketch for the Retrokits RK-002 cable that does exactly that. But you must be a bit computer-savvy with some basic knowledge of coding in C (and some time to spare). Not an overly complicated project though. Nice for a long winter evening…

ghettofroufrou · 2020-02-28T16:00:03.294Z

Hello, for me program change works but it change after the end of the pattern (16 to 64 steps), do you thinks there is a way to change it directly ? Thank

FreddyUnreal · 2020-02-28T17:43:34.541Z

I believe you can change in pattern settings. Press FUNC + PATTERN. then adjust P CH LEN. I think…I’m not by mine to verify.

ghettofroufrou · 2020-02-28T19:59:15.940Z

Thank you, you mean func+bank ?
I tried with func+bank
Tried to change use pat set to 256/15
Tried to change plays free then trig quant to direct
Tried a lot of settings but no changes

ghettofroufrou · 2020-02-28T20:26:54.751Z

20200228_2115164032×3024 3.54 MB

20200228_2114524032×3024 3.34 MB

20200228_2114454032×3024 3.11 MB

20200228_2114264032×3024 3.43 MB

maybe something to tweak in these menus.

FreddyUnreal · 2020-03-02T19:27:45.824Z

Hi. I’m pretty sure it’s the use pattern set. parameter. I’ll let you know when I’m at my OT later. I forgot to check when I got home the day I responded.

FreddyUnreal · 2020-03-04T05:21:06.747Z

Use pat set determines how many steps after a pattern change command that pattern will change.

ghettofroufrou · 2020-03-05T15:08:58.827Z

Thank you, I tried in chain behavior but it’s minimum 2/16 no direct I think it’s not possible, I don’t know why.

KaOsphere · 2020-03-05T16:11:49.346Z

ghettofroufrou:

2/16 no direct

That’s a common ̶f̶l̶a̶w̶ feature of the whole elektron line unfortunately. I won’t go back to the ̶o̶b̶s̶c̶u̶r̶e̶ technical reasons behind this ̶r̶i̶d̶i̶c̶u̶l̶o̶u̶s̶ ̶l̶i̶m̶i̶t̶a̶t̶i̶o̶n̶ safe behaviour, there are tons of threads discussing this ̶i̶s̶s̶u̶e̶ clever implementation of program changes.

If you want to bypass this, one solution is to use a midi processor :

Each time your master will send a pc the midi processor will delay the pc message, stop the sequencer, send pc message and relaunch sequencer. Works like a charm.
The other workaround could be to send pc 2 beats before you actually want it to change. It implies that you have a device which can do that.

This post contains some technical solutions despite obvious trolling in the first part please flag responsibly.