FOUT does not remove clicks or make much sense actually

Microtribe · 2022-06-28T10:35:01.164Z

sezare56:

Amp Settings, set HOLD to 15 (steps values), Release to taste.

This. Altering the playback machine fixes most issues. Don’t forget octatrack is designed to transform samples!
Also, the source material does have a lot to do with it. If there’s reverb or other spatial effects, long envelope release etc

sezare56 · 2022-06-28T10:39:26.507Z

Coming from loopers with automatic crossfade, OT gave me headaches ! But it has other strengths. Can’t be simple.

nicolas1 · 2022-06-28T10:50:10.247Z

sezare56:

Coming from loopers with automatic crossfade, OT gave me headaches ! But it has other strengths. Can’t be simple.

Which loopers can you recommend with automatic crossfade?

sezare56 · 2022-06-28T11:43:21.200Z

nicolas1:

Which loopers can you recommend with automatic crossfade?

I think all dedicated loopers use automatic crossfade ! I prefer midi sync loopers.

I like Boss loopers, especially RC 505, sold for MKII version.
Really good to make 5 stereo loops with different lengths (up to 2GB recordings !) you can remix on the fly with track fx and faders.

Finally I bought a second hand RC500 for Syntakt reasons, and for a small guitar setup (with HX STOMP). I’ll see if it will match an OT+ST setup. I’d want OT master. I’d be able to record 2 longer loops with the RC500, with free length, other (mangled) loops with OT, matching pattern length.

Timestretch fluctuations with RC loopers if slaved. With RC500 I got freezes sending too much midi data for playback control, drums sequencing. Btw this is a good feature (possibility to sequence drums with notes), you can also find on RC 505 MKII.

Pigtronics, EHX, Aeros…

darenager · 2022-06-28T11:47:05.286Z

Amp env on OT is surgically good, by far the best on any sampler I ever used.

sezare56 · 2022-06-28T11:48:23.896Z

darenager:

sampler I ever used

How many ?

darenager · 2022-06-28T13:11:52.688Z

42

sheathe · 2022-06-28T13:16:34.976Z

Ah, I love the minutiae of zero crossings in the morning.

ericd · 2022-06-28T13:49:42.663Z

sezare56:

it adds a fade out AFTER the end of the recording.

Fin25 · 2022-06-28T13:59:54.001Z

Me reading this thread…

taking-notes694×386 3.1 MB

sezare56 · 2022-06-28T14:00:36.847Z

ericd:

And the curve is almost constant. If you increase FOUT, it adds silence. Same for FIN. Here is an example with a 64 steps recording, FIN and FOUT set to 32 (Pickup recording)

image1380×712 317 KB

Clickup Machines - #38 by wolfgangschaltung

@Fin25 More notes to take in above thread.

Fin25 · 2022-06-28T14:07:02.040Z

sezare56 · 2022-06-28T14:10:56.529Z

OCTA-SLEEP1920×1080 300 KB

Annihilation_Squares · 2022-06-28T14:14:44.615Z

Same here!

sheathe · 2022-06-28T14:17:21.747Z

Haha I used to read the manual on my phone back when I was pushing my oldest son in the stroller, years ago.

Supercolor_T-120 · 2022-06-28T16:06:11.798Z

Just out of curiosity, are the people having problems with clicks using an external clock source? If you’re having problems with clicling loops and you use external clock, try switching to internal clock and see if that fixes it. That’s definitely not the only thing that can cause them, but it’s a likely one and I don’t see it mentioned much in conversations about clicks or sync issues.

I’ve never successfully gotten the OT to work reliably with any external clock at all, and one of the issues is that because even the most stable MIDI clock isn’t even close to sample accurate, ANY kind of looping audio has inconsistent pops and clicks at the loop point with external sync. Preumably dedicated loopers are all designed to not do this, probably they record a few hundred extra samples at the end of the loop and crossfade that with the start of the loop or something along those lines, but the OT doesn’t so it’s a lot more susceptible to clicks.

Pickup machines in overdub mode might have less trouble with this but I will never know because I don’t think I’ve ever gotten a PUM to complete one full loop with external clock before it gives an error and stops, and I’ve never been able to even start overdubing without an error.

If I’m in a situation where the OT can’t be the master clock, I don’t sync it a all - I send transport and tempo control from the actual master clock source to start it in time and then let it run free. It’s internal timing is so tight that I’ve started it from Reaper and let both run free for over two hours without any noticeable drift at all. Literally over 100 times (between streams and practicing I’ve done about 96 or 97 sessions like that in the duo I do most of my streaming with). The OT timing is as stable as any piece of gear I’ve used in my life, as long as it’s the master, but with external clock it’s really only OK if you don’t use flex machines for seamless loop recording or playback USING TRIGS (it’s the timing of the trigs jittering with the external clock that seems to be the issue, so playsfree tracks or endless loops that are started with a one shot trig and then run independent of the sequencer haven’t caused trouble for me), and don’t even think about pickup machines.

FreddyUnreal · 2022-06-28T17:59:46.464Z

3 years in. I really thought FOUT was doing something to the end of my sample. Granted I’m mostly a thru machine guy and use my OT as main mixer, but…

Octagonist · 2022-06-28T18:04:07.131Z

Supercolor_T-120:

If you’re having problems with clicling loops and you use external clock, try switching to internal clock and see if that fixes it.

Try saying that in Jay-Z’s cadence.

Rhythmuskorb · 2022-07-21T11:58:15.222Z

Sooo, it basically only exists for use with pickup machines?

nicolas1 · 2022-07-21T12:16:13.722Z

I can confirm that using internal clock instead of external clock does solve some of the click issues. At least now the clicks at the loop point are consistent.

I was using an E-RM Multiclock as the external clock. Now I am using the Octratrack internal clock.

Still no solution to predictably fade/crossfade them out of course.