Digitakt II 1.01A : Bug reports

DesertedIsland · 2024-05-02T19:40:43.660Z

After assigning sample to a track, sampling screen window gets messed up. All works though.

avantronica · 2024-05-02T19:59:13.521Z

similar examples of these rendering / absent artefacts were reported and addressed during testing … it’s much more likely to get a fix if next time you try to recall and note exactly what steps had preceded it, or to ideally be in a position to document the steps which repeat the outcome

even when the functionality is not impacted or it takes just going in/out of a page to tidy it, it still needs to be trapped as a specific bug to get fixed, easier said than done

tomvidm · 2024-05-02T20:20:48.757Z

Changing filter type while an LFO is routed to a selectable filter type parameter will visually display the new filter, but the one routed to by the LFO will still be in effect

avantronica · 2024-05-02T20:43:03.904Z

For anyone coming to write about crackling audio the beta firmware resolving this is released now - it changes nothing else whatsoever, so it is safe to download whether you are affected or not, just don’t look for other changes if you are not affected.

See here

Digitakt II crackling and noise on right channel Digitakt

We have now released OS 1.01A, a hotfix that addresses this issue. Thank you to everyone who assisted in verifying the solution!

frekvencia · 2024-05-02T21:15:15.696Z

Did anyone notice that adjusting the micro timing feels laggy? I.E. the micro timing slider doesn’t react immediately after pressing the left/right buttons.

Elekktrikk · 2024-05-03T04:26:09.899Z

Transfer had crashed many times, this started at +Drive filled > 10GB
now I have corrupted samples in some folders
I cannot delete folders in Transfer
I cannot delete folders on DT2 (“Folder not empty”)
If I select all samples and delete on DT2 it says for example “deleting 81 samples”, then freezes

@elektron is there a limit in path length on the device?

Elekktrikk · 2024-05-03T04:32:41.340Z

With Transfer 1.8:
- cannot backup some Projects - Read: permission denied
  (in single projects, not all)
- Edit: this is true for imported DT1 projects only
Crashes not only when writing but also during backup

dustanddrones · 2024-05-03T05:04:05.275Z

I have opened a ticket about this issue two days ago, when your +DRIVE is corrupted it becomes impossible to sample or resample, because every new file will be corrupted too.

The only solution is to format your +DRIVE if you want to use your DT II or wait for a firmware update.

Elekktrikk · 2024-05-03T06:25:13.525Z

Yes, will format, factory reset and try again.

The first chunk of my library transferred without problems, even with nested folders and long path names.

Problems occurred at > 10GB transferred data. And lost connection and freezing happened with increasing frequency until problems like corrupted data and permission problems occurred.

DesertedIsland · 2024-05-03T07:54:17.675Z

Elekktrikk:

I cannot delete folders on DT2 (“Folder not empty”)

If you select all samples in the folder and delete them first, then you can delete a folder. Not sure it is a bug, more like a safety feature.

dustanddrones · 2024-05-03T08:41:02.995Z

Unfortunately with the corrupted +DRIVE bug it is impossible to delete neither the files alone or the folders.

LyingDalai · 2024-05-03T08:55:24.096Z

You should be able to delete them from the machine itself, at the very least.

James_Orvis · 2024-05-03T09:01:18.335Z

So the most exciting feature for me is buggy as hell! Elektron need to thoroughly retest midi track functionality and bugs in that area, I ran into multiple bugs listed below. It usually starts off working fine and then it goes sour.

Tried saving midi track preset that I made on track 9 and Digitakt froze, had to reset
Midi buggy in general, can work one minute, then switch pattern stops working when returning, no midi data been picked up in Ableton. When loading a midi preset that was previously saved it doesn’t work.
On reboot midi tracks work again, but if I go to a new pattern and load my midi preset, midi tracks stop working on all patterns until reboot.
Track 16, Val 13, 14, 15 on midi track dont send midi date at all, even after reboot.
Digitakt crashed again when trying to load preset (conflict with midi track behaviour?). With midi track preset loaded on pattern 16 bank 2, this happens every time after rebooting.
I loaded midi preset on tracks 9-16, after rebooting only track 9 would work.

Note: I am sending midi via channel 10, cc numbers 16-32

LyingDalai · 2024-05-03T09:13:37.919Z

What would be good is to give as much information you could to reproduce this: what’s your midi configuration, what cables are plugged, are you using a USB MIDI hub?

James_Orvis · 2024-05-03T09:18:11.803Z

Yeah I could, but I have got a lot of work to do today and there is that many bugs that it would be very easy for Elektron to identify what’s going on. Im doing exactly the same stuff on the Digitakt 2 as I was last week with Digitakt 1, with the same routing, cables, everything and same midi channels and CC’s. I am very thorough, there is no midi clashes, wierd midi loopbacks and any settings that need to be disabled are disabled.

My guess is midi hasn’t been thoroughly tested before launch as it won’t be top of the list against all the other features.

dustanddrones · 2024-05-03T09:24:16.277Z

No, the machine freezes when you try to do this.
The bug is known by Elektron.

Elekktrikk · 2024-05-03T09:26:06.288Z

Thats normal linux fs behavior. In terminal you just type rm -rf Would be good just be asked by DT2 if I knew what I was doing and that this folder to be deleted has x subfolders and y samples.

Edit: with the corrupted fs I could not delete certain files or folders, neither on the machine nor with transfer.

sezare56 · 2024-05-03T09:37:53.477Z

UI bug : SRC slots list popping up after SRC button press. Persists after reboot. Known bug ?

Seems to happen after picking a sample in +Drive. (Select an empty slot with SRC SAMP, press YES, select a sample)

frekvencia · 2024-05-03T09:59:57.444Z

You have enabled the “remember sub-page option”. I don’t know if the behavior counts as a bug or not but it happens on other Digi boxes as well.

sezare56 · 2024-05-03T11:32:49.375Z

frekvencia:

You have enabled the “remember sub-page option”. I don’t know if the behavior counts as a bug or not but it happens on other Digi boxes as well.

What makes you think it is sub-page option related ?
I disabled it, same problem.

Definitely buggy and very annoying. I remember vaguely it happened to DT1 users, but for other Digis I don’t get what would be the equivalent. Seems too sensible depending on encoder position : moving it slightly can solve the issue.
Anybody experiencing that with DT2 or DT1?