Big problems with effects

Diayse · 2015-02-25T13:21:11.000Z

If you want to compress each track, and use the individual outputs, you need as many compressors as outputs.

If you only have one compressor, once the signal goes into it, you can’t “separate” the individual instruments to send them on the individual outs. It’s technically not possible.

So what you want to do would require 8 compressors.

Same for the delay and reverb : If you want the reverb signal of your kick only to send it to the kick individual out, then you need a reverb and delay that is only for the kick.

Same thing for all instruments.

So you need 8 compressors, 8 distortions and 8x2 digital effects.

Not the same price, not the same use.

ajs · 2015-03-06T18:49:27.000Z

""Loom"":

But nobody told us that the FX and Comp only works on the master channel. They are making promotion with their FX/Comp and single Outputs, but dont say that this just works on main out.

That is an unfair statement.

The specifications says
MASTER EFFECTS:
Analog Stereo Distortion
Analog Stereo Compressor

The other effects are listed as SEND.

http://www.elektron.se/products/analog-rytm?section=specs

The “promotion” is clear.

Loom · 2015-03-20T01:11:46.000Z

""ajs"":

Loom:

But nobody told us that the FX and Comp only works on the master channel. They are making promotion with their FX/Comp and single Outputs, but dont say that this just works on main out.

That is an unfair statement.

Okay if had seen this tab i propably could know it. Your’re right!
But but i mean promotion whise they dont tolld that. And on the packaging i mean its doesn’t markt too. But i’m not really shure about that and don’t wanna say something wrong.

I was a little bit explosiv becaus i was so pissy that there are just master reverb/delay. Because compared with elektron sequencer it could give some nice possibilitys.
Beside this i can’t use the compressor

JayNem83 · 2016-10-07T03:48:32.953Z

I just had this problem after playing in performance mode. Both delay and reverb dropped. Even though I have the levels high on both the amp and fx page. Did you a fix. Please help!

JayNem83 · 2016-10-07T05:06:34.410Z

So i was just just using the performance mode in one of the pads. Everything was fine. But once I released the pad i was using the performance mode on. Two separate tracks reverb and delay dropped. Both tracks levels on Amp and the fx page haven’t moved, but you can barely hear any reverb or delay at all now. I even tried turning up the volume and delay on both pages, but there was little change that you could notice. Has anyone else experienced this? Its driving me nuts!

Any help would be great

LyingDalai · 2016-10-07T05:08:25.947Z

Seems to me that your FX suddenly got back to the legacy mode…

riotghandi · 2016-10-07T05:29:06.210Z

check reverb and delay volume in fx section

riotghandi · 2016-10-07T05:29:36.331Z

and us pre rvb and dly setting compressor at disto page

JayNem83 · 2016-10-07T12:28:56.049Z

My Legacy mode is off, and all of my volume levels are as high as they can go. I switched the delay and reverb and delay to pre and it did give it some a boost that it still had. Ive never switched those settings since i can remember buying the machine. Do you guys keep your delay on pre? Is my machine buggy after the update? or am i just loosing my mind

JayNem83 · 2016-10-07T12:41:21.471Z

I just switched to a new project and the reverb was fine. when i switched back. i set all of my reverb and delay settings to the same parameters, and it is still non existent

LyingDalai · 2016-10-07T12:42:22.733Z

Maybe your project is crippled ?
Do you replicate this on another project ?

When you update, best thing to do is save your current project, create a new one, save it, update, get back to your project.
(© @AdamJay)

JayNem83 · 2016-10-07T12:50:47.590Z

hmmm. well i made this project after updating to 1.30. if i save this project that has the faulty fx. bounce this over into a new project. I will need to update the machine again?

LyingDalai · 2016-10-07T13:10:09.726Z

No, if this project was made after the update, it’s not crippled from the updating operation obviously

Damn. Have no clue was passiert.

=> Ticket to !!

stutech · 2016-10-07T15:11:34.014Z

and the “send to fx” routing is all in the green too, right? just a thought…

JayNem83 · 2016-10-07T15:24:15.485Z

I’m not sure. Where is the “send to fx” ? I stepped away from the unit at the moment

subbz2k · 2016-10-07T15:28:54.996Z

havent read the thread so this might already be answered. but here’s my answer to your question:

do you use individual outs for your tracks? if you do its pretty normal that you dont hear the effects. they are on the main out only. but its not a big issue - just make a track for the main out from the rytm and record/monitor that as well. now your effects are back again and you have the freedom to work on them separately. its a bit weird but i got used to it and it really has some advantages (sidechain your whole fx-track, adjust the levels afterwards, eq the fx-track and so on)

LyingDalai · 2016-10-07T15:36:11.696Z

@subbz2k here is the starting post

Big problems with effects Analog Rytm

So i was just just using the performance mode in one of the pads. Everything was fine. But once I released the pad i was using the performance mode on. Two separate tracks reverb and delay dropped. Both tracks levels on Amp and the fx page haven’t moved, but you can barely hear any reverb or delay at all now. I even tried turning up the volume and delay on both pages, but there was little change that you could notice. Has anyone else experienced this? Its driving me nuts! Any help would be grea…

JayNem83 · 2016-10-07T15:38:02.198Z

Thanks man! But I read this above as well and I actually only run through the main outs. It’s weird how the fx are fine when I change to a new project. Even if I have all parameters and fx settings set the same. Im thinking it has to be a bug in the performance mode. That’s when it dropped. When I unmuted both faulty tracks while in performance mode

LyingDalai · 2016-10-07T15:42:23.959Z

Maybe, just to test this, try to set “Legacy FX” on, try to play with your pattern, then set is off, see if you notice a change.

Another thing : when you play with a Performance pad (or a Scene), it stays stuck if you go to another page (e.g. mutes) until you come back to the Perf (or Scene) page and unlock the pad by hitting it.
When a Perf or Scene is locked like this, the Perf (or Scene) LED is showing a little bit of light…
You know this ?
Have you checked this ?

William_WiLD · 2016-10-07T16:06:27.376Z

Loom is not coming back on his thread since 13 days guys, I guess he find the solution