AR and lemur for ipad and maybe with monomachine

benwadub · 2015-01-16T22:14:49.000Z

yes, i found each cc number needed, i think the AR can t pass midi from usb to midi din thru. am i wrong?

avantronica · 2015-01-17T08:06:23.000Z

""benwadub"":

yes, i found each cc number needed, i think the AR can t pass midi from usb to midi din thru. am i wrong?

Yeah, DIN Thru for DIN In only !

alfred · 2015-01-17T09:35:29.000Z

You can use iRig MIDI instead of the camera connection kit. Works fine with Lemur.

avantronica · 2015-01-17T09:46:59.000Z

never tried it, but i think lemur can address multiple midi devices, so you could use the cck and a usb hub, but you’d need a usb>din device for monomachine (assuming it is not usb class compliant) or if you had an A4 just another usb lead (powered usb hub btw, again not tested)

benwadub · 2015-01-17T12:15:29.000Z

thanks for the help, si i need a midi interface. any advice on an interface that can powering the ipad when it s plugged?

benwadub · 2015-01-17T12:52:52.000Z

i ll check it thanks

avantronica · 2015-01-17T13:01:08.000Z

i like the sound of the i4+, bit pricey as a casual purchase, the irig mentioned above allows a powering connection, at least for older devices, if you’re after a basic (battery only) 30pin one, the line6 midimobilizer2 is about 10euro, handy for old devices(os) that don’t play with cck

benwadub · 2015-01-17T13:33:54.000Z

i think i ll go for the iconnectivity, do you think i ll be able to route audio to my zoom h1 via usb?

avantronica · 2015-01-17T14:00:12.000Z

i’m guessing you have one Baddcr, guessing the 4, i read that some supposed and popular usb class compliant devices do not work on the host port (which you’re inferring is midi only above) - so how do you find it ease of use wise and standalone, is it easy to tell what patching is happening or is that down to you to remember about merging and through and routing - i think i dismissed them as a bit of a nkotb prematurely

so theoretically, if you had lemur via cck, that ties up a ‘square’ usb port, so connecting a RYTM via usb requires the host port, or is the host port only for controllers (nano pad etc)

no big deal as it’s outta reach, but curious for putting it on the radar or not !

benwadub · 2015-01-17T14:15:48.000Z

if you could try for me that s would be nice thanks!

avantronica · 2015-01-17T14:26:57.000Z

i’ll check out the forums if the price drops a bit, as it stands i think i can get by when i need to with the raspberry pi as a usb class compliant midi hub where controller x can connect to device y & z e.g (particularly with the new pi which has more usb ports) - pi may not be ideal, haven’t thought hard about latency, but it didn’t seem an issue, good thing is it’s flexible, cheap and small - i have little interest in iPad as an audio source, so i won’t miss that aspect, i just can’t engage with it on that level - anyway, cheers for fbk

avantronica · 2015-01-17T15:44:20.000Z

yeah, the midibud would be a good thing to have around, i’d had that bookmarked, my arduino will get pushed into a cv project soon i hope, diy is always the best way in my books, thus pi and lemur, but it all takes time and UI tinkering on things like Lemur are a rabbit hole, especially since they introduced canvas, a million things half finished

avantronica · 2015-01-17T16:50:29.000Z

i’m sure it’ll be ok w midi ports, it was whether the usb side could be harnessed and reserved for control, thus leaving the DIN for sync so thrus can be used between boxes, i think(hope) a powered hub will work in both cases, whether cck or 4+, interesting to hear 'bout it anyway

benwadub · 2015-01-18T17:24:28.000Z

i m back to you for help! i try to make a lemur template for the AR
i have mapped each parameters of the AR on my template, some works, other no, maybe i have made wrong assiniation,
but my question is how to have bidirectional cc send?

avantronica · 2015-01-18T19:22:39.000Z

Shouldn’t be a problem, but you’ll need to program it carefully to prevent loops potentially, best bet if you’re struggling is to head over to the liine forum or look for similar templates

benwadub · 2015-01-19T19:31:59.000Z

nice every things is allright all the midi implementation of the rytm is on my template and works fine!
now i d like to know if it s possible to:
have the rytm sending all the pot position at the startup of lemur, do you know if it s possible?

avantronica · 2015-01-19T20:54:18.000Z

Not presently unfortunately, send a snapshot or preset From Lemur to get sync, not ideal, but best for now !

benwadub · 2015-01-19T21:55:29.000Z

ok so my template is nearly finished!
anyone interested in that template when finished?
for the moment i have a container with a tab for each track and all parameters of the track available on each tab

image.jpg2048×1536 270 KB

i just began an other page for a general mixer, with volume, pan, mute,solo,delay and reverb send of each track on one page

Neilmcm1975 · 2015-01-20T11:11:16.000Z

""benwadub"":

ok so my template is nearly finished!
anyone interested in that template when finished?
for the moment i have a container with a tab for each track and all parameters of the track available on each tab
image.jpg2048×1536 270 KB

i just began an other page for a general mixer, with volume, pan, mute,solo,delay and reverb send of each track on one page

I would be looks very nice

TaughtMe · 2015-01-20T22:00:02.000Z

Im interested!

Are there other templates around for Lemur and AR?