Anyone using a Bitstream 3x?

PeterHanes · 2018-06-18T15:14:18.000Z

space_skeleton:

Is it possible to use chained midi messages to send out double CC information on two different channels?

Yes. Check the section of the manual titled “Chain of controls” (page 26 and 32).

phesago · 2018-06-18T15:43:12.590Z

And to further elaborate on this - the free Software editor is a must with this device. Its really really easy to use. You can basically “chain” cc’s all over the place. Each “control” on the unit can chain cc’s. Its essentially a “scene machine” if you think about it in elktron terms.

Down load the software - trust me. Itll make it seem like magic once you get used to it.

space_skeleton · 2018-06-18T15:44:03.868Z

From what I’ve read on that, it still requires me to waste one of my knobs for that parameter for the grouping (Eg I will have to assign a knob that track volume and then assign it to that one fader which is also controlling another CC).

Considering I’m losing out on 4 knobs on just track volumes alone, nevermind panning or FX sends… Can I go across different scenes? It doesn’t specify that (and I’m also posting without it in my face)

phesago · 2018-06-18T15:45:53.061Z

Not correct! The way its used is each knob has a cc. You chain controls. If you want filter cutoff, volume and panning. You chain knob 1 to knob 2 and knob 2 to knob 3. Make sense?

phesago · 2018-06-18T15:46:38.001Z

I can out together a short video tonight or tomorrow if it helps.

wminor · 2018-09-08T00:53:38.864Z

phesago:

Its essentially a “scene machine” if you think about it in elktron terms.

@phesago I’m not sure I get what you mean. Please can you elaborate?

I’ve owned an A4 and a Digitakt, and I don’t remember using the word “scene” for anything!

I’m asking because I have one of these which I bought back in 2008 for a specific purpose and haven’t touched since. I just found it again, and am wondering what fun things I might be able to do with it.

PeterHanes · 2018-09-08T01:11:02.515Z

The Octatrack and Analog Rytm have “scenes” which are basically sets of parameter values that can be selected simultaneously using one physical control. The Bitstream 3X has a similar capability. The closest thing on the Analog Four would be a performance macro.

wminor · 2018-09-08T03:27:01.395Z

Oh, that’s cool. Thanks for explaining.

Excited to play with this now!

phesago · 2018-09-08T16:38:37.351Z

When I get bak home, Ill actually open the software for the bitstream 3x and show you what I mean. I forgot up until now I was supposed to provide information some time ago but I forgot. Ill get to that today in the next few hours.

phesago · 2018-09-08T16:39:51.310Z

Cool thing about the bitstream with the analog four is you can set knobs on the 3x to control multiple perf mode knobs, or expand the number of perf modes. its kind of a “your imagination / fiddling / experimentation is the limit” thing.

pseen · 2018-09-08T20:29:46.300Z

I want to hear more about that!

phesago · 2018-09-08T23:26:39.585Z

Having some trouble getting the editor to load on my pc. ill post back when this is resolved

phesago · 2018-09-09T19:51:32.842Z

3x.JPG992×864 126 KB

HEre is just a simple example.

1 - chose a midi cc. You can slo do use defined if youre more savy with sysex. Im still teaching myself this stuff, so I dont have a lot of advice/tips, but it can potentilly open it a bit more.

2- here is where you chain controls together. As you can see, you can literally map man controls in succession. You can kind of plan it out as well so you can approach this is a systematic fashion. Ive been dedicating the bottom row of knobs for chained control master groups (if that makes sense) and kind of simplifying what knobs do what as I go up. As far as the anlog four goes, as Long as you know what controls the perf knobs are (channel / cc) then you can do all sorts of cool shit.

Now, granted, I havent dug as deep as I would like, but as long as you use the editor, this device is really easy to use. If you understand sysex enough to write midi strings, then I think it can be quite a useful tool. Either for 200 bucks its a pretty rad box.

pseen · 2018-09-12T19:40:27.878Z

Cheers, will have a look into when I get some time.

re5et · 2018-09-12T21:32:45.504Z

the is probably one of the last remaining controllers i havent bought yet , it looks to have a lot of control over things (much more than most that only offer midi cc / note / basic range of values).

it looks good… perhaps one day i’ll try one.

NSM · 2019-03-14T21:21:11.944Z

I can totally recommend the Bitstream. Its feels like its really made for controlling the OT. Got my filters and delay of each channel mapped to the knobs above the faders of each channel on the BS. Pretty neat. Put the master delay time on the ribbon ctrl for some master delay madness. I actually don’t need to touch the OT at all when messing with it live. It took some time to set up. I got it back when I was using the MnM/MD/OT trilogy and I had it mapped to all 3 machines and could switch which one I wanted to ctrl on the BS. One thing that I really struggled with was to map the joystick to the joystick of the MnM - Until today I haven’t figured out what the deal is… Even though the keyless MnM doesnt have the joystick it does have the parameter for it… Has anybody found a use for the joystick on any of your other machines? What did you map it to?

PeterHanes · 2019-03-15T00:24:19.578Z

NSM:

One thing that I really struggled with was to map the joystick to the joystick of the MnM - Until today I haven’t figured out what the deal is… Even though the keyless MnM doesnt have the joystick it does have the parameter for it

According to the manual, and my aging memory, incoming Pitch Bend messages control the joystick left and right destinations, Mod Wheel (CC 1) messages control joystick up destinations, and Breath Control (CC 2) messages control joystick down destinations.

PeterHanes · 2019-11-09T19:13:14.672Z

grra:

My main consideration is that Bitstream 3x almost 13 yr old, probably all support dropped down, or I can steel try to use it with my mbp running mac os mojave?

All active support stopped several years ago, but the device will still work well. It doesn’t need any driver software to work. Just connect it to your computer via USB (or MIDI).

grra:

controller can be hookup with other gear with midi, but how he would send correct data? Is there some software that need to pre-adjust before use, or that can be done solely on Bitstream menu?

A lot of configuration of the messages sent by the Bitstream can be made on the unit itself. Advanced customization can be made on the Configuration software. This software still runs on mac OS 10.14 Mojave, but the Configuration software and the Firmware Upgrader software are 32-bit applications and so will not run natively on mac OS 10.15.

I advise you to download the manual and the Configuration software from the Wave Idea website:
http://www.waveidea.com/en/products/bitstream_3x/

PeterHanes · 2019-11-09T20:54:44.034Z

grra:

maybe that not for this thread, but can you tell me pls do that controller worth hassle in 2019 or maybe you know some good, more modern alternatives too it?

You should search the forum and read about other controllers. This topic is about the Bitstream. The answer to your question will depend on exactly what you want to achieve with a controller: if necessary, make a new topic to say specifically what your needs are.

grra:

One that interesting me, second hand (ofcourse), have joystick problem, overall looks pretty decent, 3.4/5 i guess, but I can’t tested all the functions (posted online), do they (Bitstreams) easy breakes or screen shutdown? I mean, test of time.

Maybe you can ask the seller to post a photo of the screen, or promise to refund you if any of the controls are broken?

Mine has worked fine for many years. They are very tough. But there are very few examples to know what the general reliability is.

analogspecies · 2019-11-18T06:44:22.645Z

my b3x is over ten years and is ok . you must clean it. he is perfekt for all elektron machines - i have my complete monomachine and octatrack in bitstream3x