A question in general: As I see the Updates for mk 1 rytm and a4 seems to be very buggy. How to react now? Is Elektron reading our threads or is it better to pull a support ticket for every new update bug?
What is the best way
Support ticket. Always.
7 Likes
Support ticket indeed, as detailed as possible!
And don’t forget to describe the bug in the correct thread (or ask Mods to create the thread if it doesn’t exist yet) so that the community is aware of it.
5 Likes
Why is there no(longer) 1, 2 and 4 snap values?
I’m not happy about this since I use those values a lot.
Please bring them back.
2 Likes
Yeah, well, it’s been solved in the Rytm section.
Someone found out that it’s about how long you hold the buttons.
Short press takes you to the normal Global menu.
If you hold the combination you go straight to the Projects list.
1 Like
fwiw
There are a few pre-existing threads for some products covering new OS issues where suspected bugs feedback may be better collated … check the respective device’s sub-forum
3 Likes
Don’t upgrade your unit if you’re not certain about all the aspects of the upgrade being to your liking. It is not recommended to downgrade the firmware, pretty sure it even says so in the documentation for each update.
2 Likes
Just send the project backup sysex? They did a good job imo of what was in store with up/downgrading.
I don’t trust new Elektron firmwares. There are a lot of sad reports on the MKII generation updates here in the forum (including this thread) and my OT has become an unreliable machine since 1.30B/C.
Thanks for that. Weird, this glitch happens occasionally. When I press yes, I get “confirmed” message but destination list appears again. It’s like knob value changes as if it turned just slightly. Hope it’s not hardware error or anything. I’ll try downgrading to see what happens.
Can anyone elucidate this new feature more: “Increased the number of LFO speed snap values.”
Is this new LFO sync values that are faster/slower?
No, it means that you can locate certain values quickly by using function as a modifier/snap key
As it stands on the original AR the snap values are(were) Min / Zero / Max
so it’s easy to add more !
the factor of speed_x_mult will determine if an LFO syncs up with the pattern, the new snap values seem to facilitate on the grid lfo rates
1 Like
Ollie responded in another thread that there have been 3 regressions across the 7 os drops, only one of them is critical.
So, either people aren’t actually reporting their bugs or there is an extensive amount of noise being made on the board over the few bugs there are.
1 Like
No issues with 1.30B and OT MKI for me.
What are yours ? I think I read it.
I don’t update systematically if everything works. Trig Conditions worth it !
well, there is a thread that came out today about people having their " machine " ( digitone and digitakt ) freeze since the last update. Thought i should mention it … at least, i won’t update before i know what’s going on
This person is referring to the digitone only. The persons just keeps referring to it as the dt.
Upgraded my digitakt as soon as the update dropped. it’s working as expected.
Not happy about some of those removed quick snap lfo values, but no issue otherwise.
2 Likes
That is correct. I am talking about my Digitone.
Just for your Information: I also updated my Digitakt from what I think was 1.08 to 1.10 and have been hammering on it since. No problems so far. Had not have any problem with the Digitakt in the past except missing the notes on trig 1 when slaved to another device. But thats another story ;)…
2 Likes
Your original post seems to have been misinterpreted by some to believe that both your digitone and digitakt have had issues since update.
2 Likes
Seems so, replace DT with DN for better understanding as these abbreviations are a lot more commonly used in the forums
2 Likes